7 Piece Fillet Weld Gauge #8...
Used for:
- Checking Fillet Leg Size
- Checking Fillet Throat Size

Features:
- Stainless Steel
- Can be Certified
Not Available for Purchase in Electronic Format

A10.1M:2007 SPECIFICATION FOR ...
This specification sets forth accepted methods for testing and describing the performance of Rogowski-type air core current sensing coils (CSC) and weld current monitors (WCM) used in the measurement of single-phase ac resistance welding currents. A definition of terms relevant to this measurement is included. CSC and system tests and calibration methods are described in detail. Detailed information that shall be made available to the user are prescribed. ISBN 978-0-87171-068-0

A2.1 DC -2012; WELDING SYMBOL ...
Easy to read wall chart to complement the AWS A2.4:2012.

Standard symbols for welding, brazing and nondestructive examination. For shop or classroom.

Chart: 11" x 17".
Not Available for Purchase in Electronic Format

A2.1 WC XL-2012 WELDING SYMBO...
A wall size (27" X 36") companion to AWS A2.4 2012 Standard Symbols for Welding, Brazing, and Nondestructive Examination, these easy to read wall chart vividly illustrate proper usage of basic and supplementary welding symbols.
Not Available for Purchase in Electronic Format

A2.4 - 1993...
A2.4 - 1993. PHOTOCOPY ONLY.
Not Available for Purchase in Electronic Format

A2.4-1998 STANDARD SYMBOLS FOR...

PRESENTS A GRAPHICAL SYSTEM, USING THE "THIRD ANGLE" METHOD OF PROJECTION, FOR INDICATING WELDING, BRAZING, AND NONDESTRUCTIVE TESTING EXAMINATION REQUIREMENTS ON DRAWINGS. PROVIDES DETAILED INFORMATION AND EXAMPLES FOR DRAWING AND INTERPRETING THESE SYMBOLS. ANSI Approved. approx. 112 pages ISBN 0-87171-524-4 ***HISTORICAL ONLY AVAILABLE AS PHOTOCOPY** Replaced by AWS A2.4: 2007

A2.4/A2.1 COMBO A2.4-2012 (Boo...
Purchase this complete set for a savings of 15%. This standard establishes a method of specifying certain welding, brazing, and nondestructive examination information by means of symbols. Detailed information and examples are provided for the construction and interpretation of these symbols. This system provides a means of specifying welding or brazing operations and nondestructive examination, as well as the examination method, frequency, and extent. Also Includes:

Easy-to-read desk and wall charts to complement AWS A2.4-2012, Standard Symbols for Welding, Brazing, and Nondestructive Examination. For desktop, drafting table, shop, or classroom use. Wall chart (WC) 22" x 28", desk chart (DC) 11" x 17", (2012).
Not Available for Purchase in Electronic Format

A2.4:2012 STANDARD SYMBOLS FOR...
Establishes a method of specifying certain welding, brazing, and nondestructive examination information by means of symbols.

Contains detailed information and examples for the construction and interpretation of these symbols. This system provides a means of specifying welding or brazing operations and nondestructive examination, as well as the examination method, frequency, and extent.

150 pages, 6 Tables, 56 Figures.

Click here to purchase the AWS A2.4:2012 version in Spanish

A3.0M/A3.0:2010 STANDARD WELDI...
Alphabetical glossary of over 1,400 standard terms and definitions for welding, brazing, soldering, resistance welding, etc., as well as hybrid processes. Each term has one clearly applicable definition, accurately reflecting the term’s use in the joining world. Includes figures to illustrate the use of terms. For completeness, nonstandard terms are also included. Contains a Master Chart of Welding and Allied Processes, an d the Joining Method Chart. 160 pages, 62 figures, 5 tables (2010).

A4.2M:1997 CALIBRATING MAGNET ...
A4.2M:1997 CALIBRATING MAGNET INSTRUMENTS TO MEASURE DELTA

A4.3-93: (R2006) STANDARD METH...
A standard 25 Ã? 12 Ã? 80 mm test specimen and method of preparation are set forth, along with two standard methods of diffusible hydrogen analysis, mercury displacement and gas chromatography. The methods are suitable for shielded metal arc welding, gas metal arc welding, flux cored arc welding, and submerged arc welding using welding conditions and electrodes given in several applicable American Welding Society filler metal specifications. ISBN 0-87171-401-9

A5-ALL ALL 34 A5 SPECIFICATION...
Save hundreds of dollars on the whole series of A5 Filler Metal Specifications

These crucial specifications give the purchaser and distributor of filler metals a dependable, efficient recognition system. The classifications defined in these standards allow you to identify filler metals uniformly, without consideration of manufacturersâ??trade names or brand names. AWS A5 Filler Metal Specifications are ANSI Approved and Dept. of Defense Adopted.

Includes new A5.22 and A5.36!
Not Available for Purchase in Electronic Format

A5.01M/A5.01:2008 (ISO 14344:2...
This document provides a means by which the information needed for the procurement of welding consumables to an AWS filler metal specification can be stated clearly, concisely, and completely. It includes a method by which the heat, lot, testing, and certification requirements that are essential to so many of today’s welding applications can be specified in the procurement document. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 978-0-87171-091-8

A5.1/A5.1M -2004 SPECIFICATION...
This specification establishes the requirements for classification of carbon steel electrodes for shielded metal arc welding. The requirements include mechanical properties of weld metal, weld metal soundness, and usability of electrode. Requirements for composition of the weld metal, moisture content of low-hydrogen electrode coverings, standard sizes and lengths, marking, manufacturing, and packaging are also included. A guide to the use of the standard is included in an Annex. Optional supplemental requirements include improved toughness and ductility, lower moisture contents, and diffusible hydrogen limits. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-642-9

A5.1/A5.1M: 1948 SPECIFICATION...
This specification establishes the requirements for classification of carbon steel electrodes for shielded metal arc welding. The requirements include mechanical properties of weld metal, weld metal soundness, and usability of electrode. Requirements for composition of the weld metal, moisture content of low-hydrogen electrode coverings, standard sizes and lengths, marking, manufacturing, and packaging are also included. A guide to the use of the standard is included in an Annex. Optional supplemental requirements include improved toughness and ductility, lower moisture contents, and diffusible hydrogen limits. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. Historical See AWS A5.1/A5.1M:2004
Not Available for Purchase in Electronic Format

A5.1/A5.1M:2012 SPECIFICATION ...
This specification establishes the requirements for classification of carbon steel electrodes for shielded metal arc welding. The requirements include mechanical properties of weld metal, weld metal soundness, and usability of electrode. Requirements for composition of the weld metal, moisture content of low-hydrogen electrode coverings, standard sizes and lengths, marking, manufacturing, and packaging are also included. A guide to the use of the standard is included in an annex.

Optional supplemental requirements include improved toughness and ductility, lower moisture contents, and diffusible hydrogen limits.

This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.

A5.11/A5.11M:2005 SPECIFICATIO...
This specification prescribes the composition, dimensions, soundness, and properties of weld metal from more than 30 classifications of nickel and nickel-alloy covered electrodes. Major topics include general requirements, testing, manufacturing, identification, and packaging. A guide to using the specification is included in an annex. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-005-6

A5.12/A5.12M: 1998(R2007) SPEC...
This specification prescribes the requirements for the classification of bare tungsten and tungsten-alloy electrodes for gas tungsten arc welding and cutting and plasma arc welding and cutting. Classification is based upon the chemical composition of the electrode. Standard sizes, finish, lengths, quantities, product identification, color coding and chemical composition limits are specified. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. Historical ISBN 0-87171-527-9. See AWS A5.12M/A5.12: 2009 NEW REVISION

A5.12M/A5.12:2009 (ISO 6848:20...
This specification prescribes the requirements for the classification of bare tungsten and oxide dispersed tungsten electrodes for gas tungsten arc welding and cutting and plasma arc welding and cutting. Classification is based upon the chemical composition of the electrode. Standard sizes, finish, lengths, quantities, product identification, color coding, and chemical composition limits are specified. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. This specification adopts the requirements of ISO 6848:2004 and incorporates the provisions of earlier versions of AWS A5.12, allowing for classifications under both specifications. ANSI Approved. approx. 27 pages ISBN 978-0-87171-747-4

A5.13:2000 SPECIFICATION FOR S...
This specification prescribes the requirements for classification of surfacing electrodes for shielded metal arc welding. Classification is based upon the chemical composition of the deposited weld metal except for tungsten carbide electrodes where classification is based on the mesh range, quantity, and composition of the tungsten carbide granules. A guide is appended to the specification as a source of information as to the characteristics and applications of the classified electrodes. ISBN 0-87171-607-0

A5.14/A5.14M:2005 (HISTORICAL)...
The chemical compositions of nearly fifty nickel and nickel-alloy welding electrodes and rods are specified, including thirteen compositions not previously classified. Major topics include general requirements, testing, packaging and application guidelines. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-007-2. See AWS A5.14/A5.14M :2009 for new revision.

A5.14/A5.14M:2009 SPECIFICATIO...
Covers the chemical compositions of 50 nickel and nickel-alloy welding electrodes and rods are specified, including three compositions not previously classified. Major topics include general requirements, testing, packaging, and application guidelines. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.

A5.15-90(R2006): SPECIFICATION...
The chemical composition requirements for electrodes and rods for welding cast iron are specified. Copper-base rods used for braze welding of cast iron are not included. Major topics include general requirements, testing, packaging, and application guidelines. ISBN 0-87171-328-4

A5.16/A5.16M: 1997 SPECIFICATI...
This specification provides requirements for the classification of solid and composite carbon steel electrodes and fluxes for submerged arc welding. Electrode classification is based on chemical composition of the electrode for solid electrodes, and chemical composition of the weld metal for composite electrodes. Flux classification is based on the mechanical properties of weld metal produced with the flux and an electrode classified herein. Other requirements include sizes, marking, manufacturing and packaging. The form and usability of the flux are also included. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. Historical see AWS A5.17/A5.17M-97: R2007
Not Available for Purchase in Electronic Format

A5.17/A5.17M-97(R2007) SPECIFI...
This specification provides requirements for the classification of solid and composite carbon steel electrodes and fluxes for submerged arc welding. Electrode classification is based on chemical composition of the electrode for solid electrodes, and chemical composition of the weld metal for composite electrodes. Flux classification is based on the mechanical properties of weld metal produced with the flux and an electrode classified herein. Other requirements include sizes, marking, manufacturing and packaging. The form and usability of the flux are also included. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-530-9

A5.19:1992(R2006) SPECIFICATIO...
This specification prescribes requirements for the classification of bare magnesium all welding electrodes and rods for use with the gas metal arc, gas tungsten arc, oxyfuel gas, and plasma arc welding processes. Classification is based upon chemical composition of the welding wire. Standard sizes, finish, winding requirements, package forms and weights, product identification, and chemical composition limits are specified. ISBN 0-87171-399-3

A5.20/A5.20M:2005 CARBON STEEL...
This specification prescribes the requirements for classification of carbon steel electrodes for flux cored arc welding. The requirements include chemical composition and mechanical properties of the weld metal and certain usability characteristics. The AWS A5.20/A5.20M specification also includes optional, supplemental designators for improved toughness and diffusible hydrogen and to indicate conformance to special mechanical property requirements when the weld metal is deposited using both low heat input, fast cooling rate and high heat input, slow cooling rate procedures. Additional requirements are included for standard sizes, marking, manufacturing and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of carbon steel flux cored electrodes. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-003-X

A5.21/A5.21M: 2011 SPECIFICATI...
This specification prescribes the requirements for classification of bare electrodes and rods for surfacing. Solid surfacing electrodes and rods, are classified on the basis of the composition of the material as manufactured. Metal cored and flux cored composite (tubular) surfacing electrodes and rods, are classified on the basis of the chemical composition of the deposited weld metal. Tubular tungsten carbide bare rods are classified on the basis of the mesh range, quantity, and composition of the tungsten carbide granules. A guide is appended to the specification as a source of information concerning the characteristics and applications of the classified electrodes. ISBN 0-87171-650-X

A5.22 95 (R2005) STAINLESS STE...
Classification and other requirements are specified for more than 40 grades of flux cored stainless steel electrodes and rods. New classifications include duplex alloys not previously classified and flux cored rods for gas tungsten arc welding. Designations indicate the chemical composition of the weld metal, the position of welding (newly introduced in this revision of the standard), and the external shielding medium required (for those classifications for which one is required). A special designation (K) is used to identify those classifications that are intended specifically for cryogenic service. The requirements include general requirements, testing, and packaging. The Annex provides general application guidelines for individual alloys and other useful information about welding electrodes. ISBN 0-87171-456-6

A5.22/A5.22M:2010 SPECIFICATIO...
Classification and other requirements are specified for numerous grades of flux cored and metal cored stainless steel electrodes and rods. New classifications include a duplex alloy and three high carbon classifications not previously classified. New classifications also include all of the metal cored electrodes that are currently in A5.9/A5.9M. In the next revision of A5.9/A5.9M these metal cored electrodes will be deleted from that specification. Designations for the flux cored electrodes and rods indicate the chemical composition of the weld metal, the position of welding, and the external shielding gas required (for those classifications for which one is required). Designations for the metal cored electrodes indicate the chemical composition of the weld metal only. The requirements include general requirements, testing, and packaging. Annex A provides general application guidelines for individual alloys and other useful information about welding electrodes. ANSI Approved. approx. 55 pages ISBN 978-0-87171-764-1

A5.23/A5.23M: 1997 LOW ALLOY S...
This specification provides requirements for the classification of solid and composite low-alloy steel electrodes and fluxes for submerged arc welding. Electrode classification is based on chemical composition of the electrode for solid electrodes, and chemical composition of the weld metal for composite electrodes. Flux classification is based on the mechanical properties and deposit composition of weld metal produced with the flux and an electrode (solid or composite) classified herein. Other requirements include sizes, marking, manufacturing, and packaging. The form and usability of the flux are also included. The specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ANSI Approved. approx. 39 pages ISBN 0-87171-531-7

A5.23/A5.23M:2011 SPECIFICATIO...
This specification provides requirements for the classification of solid and composite carbon steel and low-alloy steel electrodes and fluxes for submerged arc welding. Electrode classification is based on chemical composition of the electrode for solid electrodes, and chemical composition of the weld metal for composite electrodes. Fluxes may be classified using a multiple pass classification system or a two-run classification system, or both, under this specification.

Multiple pass classification is based on the mechanical properties and the deposit composition of weld metal produced with the flux and an electrode classified herein. Two-run classification is based upon mechanical properties only. Additional requirements are included for sizes, marking, manufacturing, and packaging. The form and usability of the flux are also included. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of submerged arc fluxes and electrodes.

This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.

A5.25/A5.25M:1997 SPECIFICATIO...
Classification requirements are specified for fluxes and solid and composite metal cored electrodes for electroslag welding. The requirements for electrodes include chemical composition of the electrode for solid electrodes and of weld metal for metal cored electrodes. Requirements for fluxes include the mechanical properties and soundness of weld metal taken from a groove weld made with a particular electrode using a prescribed welding procedure. Standard electrode sizes, marking, and packaging requirements are included. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.
Not Available for Purchase in Electronic Format

A5.25/A5.25M:1997(R2009) - SPE...
Classification requirements are specified for fluxes and solid and composite metal cored electrodes for electroslag welding. The requirements for electrodes include chemical composition of the electrode for solid electrodes and of weld metal for metal cored electrodes. Requirements for fluxes include the mechanical properties and soundness of weld metal taken from a groove weld made with a particular electrode using a prescribed welding procedure. Standard electrode sizes, marking, and packaging requirements are included. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ANSI Approved. approx. 30 pages ISBN 0-87171-539-2

A5.26/A5.26M:1997 SPECIFICATIO...
Classification requirements are specified for solid and composite flux cored and metal cored) electrodes for electrogas welding. The requirements include chemical composition of the electrode for solid electrodes and of weld metal for composite (cored) electrodes, in addition to the mechanical properties and soundness of weld metal taken from a groove weld made with these electrodes using the prescribed welding procedure. Standard electrode sizes, marking, and packaging requirements are included. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-532-5

A5.29/A5.29M:2005 LOW ALLOY ST...
This specification prescribes the requirements for classification of low-alloy steel electrodes for flux cored arc welding. The requirements include chemical composition and mechanical properties of the weld metal and certain usability characteristics. Optional, supplemental designators are also included for improved toughness and diffusible hydrogen. Additional requirements are included for standard sizes, marking, manufacturing, and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of low-alloy steel flux cored electrodes. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-011-0

A5.2:1992 SPECIFICATION FOR CA...
This specification prescribes the requirements for classification of carbon and low-alloy steel rods for oxyfuel gas welding. The classification requirements include the mechanical properties of the weld metal. Additional requirements are included for chemical composition of the rod and for manufacture, sizes, lengths, and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of the rods. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. Historical See AWS A5.2/A5.2M:2007
Not Available for Purchase in Electronic Format

A5.30/A5.30M:2007 SPECIFICATIO...

Five classes (cross-sectional design) of consumable inserts of various chemical compositions are described. Each class is subdivided into two or three styles (based on the shape of the insert). Topics include the chemical composition, general dimensional requirements, packaging, and application guidelines.

A5.31M/A5.31:2012 Specificatio...
Eighteen fluxes for brazing and braze welding are classified according to the filler metal, form, and activity temperature range. Classification is in accordance with a classification system that employs the designator “FB” to indicate fluxes for brazing and braze welding applications.

In addition to selected tests for each classification, major topics include general requirements, testing procedures, and packaging requirements. An annex listing general application guidelines is included.

This specification makes use of both the International System of Units (SI) and U.S. Customary Units. The measurements may not be exact equivalents; therefore, each system shall be used independently.

A5.32/A5.32M: 1997 SPECIFICATI...
This specification for welding shielding gases specifies minimum requirements for the composition and purity of the most popular single-component shielding gases. Classification designators for both single and multicomponent gases are introduced. Other topics include testing procedures, package marking, and general application guidelines. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ANSI Approved. approx. 20 pages ISBN 0-87171-523-6 Historical See AWS A5.32/A5.32M (R2007)

A5.34/A5.34M:2007 SPECIFICATIO...
The composition, soundness, and properties of weld metal from nine grades of flux cored electrodes are specified. Standard electrode sizes together with their package forms and package sizes are detailed. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 978-0-87171-072-7

A5.4/A5.4M:2012 SPECIFICATION ...
Composition and other requirements are specified for more than forty classifications of covered stainless steel welding electrodes. The requirements include general requirements, testing, and packaging.

Annex A provides application guidelines and other useful information about the electrodes.

This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.

A5.5/A5.5M:2006 SPECIFICATION ...
This specification prescribes the requirements for classification of low-alloy steel covered electrodes used for shielded metal arc welding. The requirements include chemical composition and mechanical properties of weld metal, weld metal soundness, usability tests of electrodes, and moisture tests of the low-hydrogen electrode covering. Requirements for standard sizes and lengths, marking, manufacturing, and packaging are also included.
Optional supplemental requirements include tests for absorbed moisture in the electrode covering and for diffusible hydrogen in the weld metal.
This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 0-87171-971-2

A5.6:1984 (HISTORICAL) COVERED...
This specification provides requirements for the classification of covered copper and copper alloy electrodes for shielded metal arc welding. It includes compositions in which the copper content exceeds that of any other element. ANSI Approved. approx. 19 pages ISBN 0-87171-241-5 (Historical - Photocopy)

A5.7/A5.7M:2007 SPECIFICATION ...
This specification prescribes the requirements for classifications of copper and copper-alloy electrodes and rods for gas shielded metal arc, gas shielded tungsten arc, and plasma arc welding. Classification is based on chemical composition of the filler metal. Additional requirements are included for manufacture, sizes, lengths and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and intended use of the electrodes. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other. ISBN 978-0-87171-640-8

A5.8/A5.8M:2011 SPECIFICATION ...
This specification prescribes the requirements for the classification of filler metals for brazing and braze welding. The chemical composition, physical form, and packaging of more than 75 brazing filler metals are specified. The filler metal groups described include aluminum, cobalt, copper, gold, magnesium, nickel, silver, and brazing filler metals for vacuum service. Information is provided concerning the liquidus, the solidus, the brazing temperature range, and general areas of application recommended for each filler metal.

Additional requirements are included for manufacture, sizes, lengths, and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of the filler metals for brazing and braze welding. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each must be used independently of the other.

A5.9-93R: SPECIFICATION FOR BA...
The classification and other requirements for more than forty-five bare stainless steel electrodes (solid and composite), rods, and strips are specified, including a number of duplex alloys previously unclassified. ANSI Approved. approx. 24 pages ISBN 0-87171-406-X Historical See AWS A5.9/A5.9M:2006

A5.9/A5.9M:2012 SPECIFICATION ...
This specification prescribes the requirements for classification of solid and composite stainless steel electrodes (both as wire and strip) for gas metal arc welding, submerged arc welding, and other fusion welding processes. It also includes wire and rods for use in gas tungsten arc welding.

Classification is based on chemical composition of the filler metal. Additional requirements are included for manufacture, sizes, lengths, and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of the stainless steel filler metal.

This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each system must be used independently of the other.

AASHTO/AWS D1.5M/D1.5:1995; BR...
This code covers the welding requirements for AASHTO welded highway bridges made from carbon and low-alloy constructional steels.
Not Available for Purchase in Electronic Format

AASHTO/AWS D1.5M/D1.5:2008-ERR...
This code covers the welding requirements for AASHTO welded highway bridges made from carbon and low-alloy constructional steels. This 2008 edition contains dimensions in metric SI Units and U.S. Customary Units. Clauses 1 through 7 constitute a body of rules for the regulation of welding in steel construction. The provisions for Clause 9 have been distributed throughout the D1.5 code. Clauses 8, 10, and 11 do not contain provisions, as their analogue D1.1 sections are not applicable to the D1.5 code. Clause 12 contains the requirements for fabricating fracture critical members. This edition incorporates the errata issued on June 10, 2009. ISBN 978-0-87171-075-8

ANSI Z49.1: 1994 (PHOTOCOPY) S...
Unions, societies, trade groups, and U.S. military and enforcement agencies including AWS, Sheet Metal Workers, OSHA, and NIOSH contributed to Safety in Welding, Cutting, and Allied Processes. Covers oxyfuel gas welding and cutting safety, arc welding and cutting equipment safety, resistance welding safety, electron beam processes, and laser beam cutting and welding safety. ANSI Approved.
Not Available for Purchase in Electronic Format

ANSI Z49.1: 2012 SAFETY IN WEL...
This standard covers all aspects of safety and health in the welding environment, emphasizing oxygen gas and arc welding processes with some coverage given to resistance welding. It contains information on protection of personnel and the general area, ventilation, fire prevention and protection, and confined spaces.

A significant section is devoted to precautionary information, showing examples, and an extensive bibliography is included.

Specific provisions for oxyfuel gas and arc welding and cutting, resistance welding, electron beam welding, laser beam cutting and welding, and – new in this edition – brazing and soldering. Generally applicable to other welding processes such as submerged arc welding and allied processes. Contains information useful to educators, industrial hygienists, engineers, and other personnel responsible for safety and health in welding.

Unions, societies, trade groups, and U.S. military and enforcement agencies – including AWS, Sheet Metal Workers, OSHA, and NIOSH – contributed in the development of this revision of Z49.1.

68 pages, 1 Table, 4 Figures.

API 1104:2005; WELDING OF PIPE...
This standard covers the gas and arc welding of butt, fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, nitrogen and, where applicable, covers welding on distribution systems. It applies to both new construction and in-service welding.

The welding may be done by a shielded metal-arc welding, submerged arc welding, gas tungsten-arc welding, gas metal-arc welding, flux-cored arc welding, plasma arc welding, oxyacetylene welding, or flash butt welding process or by a combination of these processes using a manual, semiautomatic, mechanized, or automatic welding technique or a combination of these techniques.

The welds may be produced by position or roll welding or by a combination of position and roll welding. 

Includes Errata 1 (2007) and Errata 2 (2008)
***NOT AN AWS MEMBER PUBLICATION***NO AWS MEMBER DISCOUNT APPLY***
Not Available for Purchase in Electronic Format

API-M:2006 STUDY GUIDE FOR API...
This study guide contains information on the use of API Standard 1104, Twentieth Edition, which will assist in the student prepare for the using the standard as well as preparing for code-related examinations. Material is provided for each of the 13 sections of the standard and both appendices. Exercise questions and answers are provided for each topic. ISBN 0-87171-049-8. See API-M:2008 for latest revision.

ASNT #8; RADIOGRAPHIC INTERPRE...
A reproduction of Section Eight from ASNT’s Nondestructive Testing Handbook, third edition: Volume 4, Radiographic Testing. Contents: fundamentals; standards, codes and specifications; visual acuity; radiographic viewing conditions and equipment; densitometers; radiographic interpretation reporting; radiographic artifacts; discontinuity indications. Authors:Hellier, Charles J. III and Wheeler, George C. 36 pages
Not Available for Purchase in Electronic Format

ASTMSW - ASTM STANDARDS FOR WE...
A compilation of all 59 ASTM Standards referenced by AWS D1.1 - Structural Welding Code-Steel. An excellent companion to D1.1. 450 pages. Available in hard copy only.
Not Available for Purchase in Electronic Format

AWN ARC WELDING AND CUTTING NO...
Measurements of the noise produced by four arc welding processes and one arc cutting process were evaluated under standardized measurement conditions. 40 pages, (1979). ISBN 0-87171-176-1

AWS A2.4:2012 (SPANISH) STANDA...
Spanish translation of A2.4. This standard establishes a method of specifying certain welding, brazing, and nondestructive examination information by means of symbols.

Detailed information and examples are provided for the construction and interpretation of these symbols. This system provides a means of specifying welding or brazing operations and nondestructive examination, as well as the examination method, frequency, and extent.

AWS A2.4:2012 Símbolos Estándares para Soldadura, Soldadura Fuerte y Examinación No Destructiva (Español)

Esta norma establece un método de especificación de soldadura, soldaduras fuertes e información de evaluación no destructiva por medio de símbolos. La información detallada y los ejemplos son suministrados para la construcción e interpretación de estos símbolos.

El sistema suministra un medio de especificación de operaciones de soldadura, soldaduras fuertes y evaluación no destructiva así como el método de evaluación, frecuencia y extensión.

Click here to purchase the AWS A2.4:2012 version in English

AWS A5.16/A5.16M:2013 (ISO 240...
This specification prescribes the requirements for the classification of over 30 titanium and titanium-alloy welding electrodes and rods. Classification is based upon the chemical composition of the electrode. Major topics include general requirements, testing, packaging, and application guidelines.

This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these are not equivalent, each must be used independently of the other.

This specification adopts the requirements of ISO 24034 and incorporates the provisions of earlier versions of A5.16/A5.16M, allowing for classifications under both specifications.

AWS A9.5:2013 GUIDE FOR VERIFI...
This standard provides guidelines for assessing the capability and accuracy of computational weld mechanics (CWM) models. This standard also provides general guidance for implementing verification and validation (V&V) of computational models for complex systems in weld mechanics.

AWS B2.1-8-215:2001(R2012) STA...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding with consumable insert root. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This WPS was developed primarily for pipe applications.

AWS D14.9/D14.9M:2013 SPECIFIC...
This specification provides standards for the design and manufacture of pressure containing welded joints and structural welded joints used in the manufacture of hydraulic cylinders.

Manufacturer’s responsibilities are presented as they relate to the welding practices that have been proven successful within the industry in the production of hydraulic cylinders.

Included are sections defining welding procedure qualification, welding performance qualification, workmanship and quality requirements as well as inspection requirements and repair requirements.

AWS D17.1/D17.1M:2010-AMD1 SPE...
This revolutionary document represents the most significant change to aviation welding standards in more than 30 years, including coverage in three areas never addressed in MILSTDs design, repair, and nonflight hardware. And, for the first time, there are authoritative procedures for weld repair of inservice existing aerospace flight hardware. In fact, the standards use of weld repair technology enables weld overhaul beyond the areas originally designated for a weld.

Bolstering the excellent coverage on inspection is information to avoid both under and overinspection, arising from the D17 Committees position that choosing acceptance criteria beyond the capability of the welding process may lead to numerous inspection rejections and increasing costs.

To help, tables on acceptance criteria one in U.S. Customary units, the other in SI units provide distinctions for Class A, B, and C welds. Also includes an annex offering Guidelines for Design, Analysis, and Fabrication of Weld Joints. D17.12001 emphasizes fusion welding of aluminum based, nickelbased, ironbased, cobaltbased, magnesiumbased, and titaniumbased alloys using electric arc and high energy beam processes. SI metric equivalents provided.

ANSI Approved. ISBN 978-0-87171-783-2

AWS G2.5/G2.5M:2012 Guide for ...
The standard Guide for the Fusion Welding of Zirconium and Zirconium Alloys provides instructional guidance for the welding of zirconium and zirconium alloys.

This guide explains:
- processes
- equipment
- materials
- workshop practices
- joint preparation
- welding techniques
- tests, and the repair of defects.

AWS YEAR MEMBERSHIP 2 YEARS...
AWS TWO YEAR MEMBERSHIP $135.00 PLUS $12.00 (ONE TIME INITIATION FEE). MEMBERS WILL GET THE MONTLY "WELDING JOURNAL MAGANIZE" AND 25% DISCOUNT IN ALL AWS PUBLICATIONS.
Not Available for Purchase in Electronic Format

B1.10: 1999 GUIDE FOR THE NOND...
This guide acquaints the user with the nondestructive examination methods commonly used the examine weldments. The standard also addresses which method best detects various types of discontinuities The examination methods included are visual, penetrant, magnetic, radiographic, ultrasonic, electromagnetic (eddy current), and leak testing. ISBN 0-87171-609-7

B1.11: 1988 GUIDE FOR THE VISU...
Gives guidance to assist in the visual examination of welds. Includes sections on prerequisites, fundamentals, surface conditions, and equipment. Sketches and color photographs illustrate common weld discontinuities.
Not Available for Purchase in Electronic Format

B2.1-1-001: 1990(R2006) (SWPS)...
This standard contains the essential welding variables for carbon steel plate and pipe in the thickness range of 3/16 through 3/4 in., using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. ISBN 0-87171-318-7

B2.1-1-003:2002 (R2013) STANDA...
This standard contains the essential welding variables for welding galvanized steel in the thickness range of 18 through 10 gauge, using semiautomatic gas metal arc welding (short circuiting transfer mode). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds and fillet welds. ISBN 0-87171-675-5

B2.1-1-007:2002 (R2013) STANDA...
This standard contains the essential welding variables for welding galvanized steel in the thickness range of 18 through 10 gauge using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds. ISBN 0-87171-679-8

B2.1-1-011:2002-AMD1 (R2013) S...
This standard contains the essential welding variables for welding galvanized steel in the thickness range of 10 through 18 gauge, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds. ISBN 0-87171-683-6

AMD: Amendment

B2.1-1-016: 1994 STANDARD WELD...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-425-6

B2.1-1-018: 1994 STANDARD WELD...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using semiautomatic self-shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-427-2

B2.1-1-020: 1994-AMD1 STANDARD...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using semiautomatic Ar/CO2 shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-429-9

AMD: Amendment

B2.1-1-022: 1994 STANDARD WELD...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-431-0

B2.1-1-027: 1998 STANDARD WELD...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1/2 inch, using semiautomatic, self-shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS is intended primarily for plate and structural applications. ISBN 0-87171-547-3

B2.1-1-201: 1996(R2007) (SWPS)...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 3/4 inch, using manual shielded metal arc welding with E6010 (vertical uphill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-488-4

B2.1-1-203: 1996(R2007) (SWPS)...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 3/4 inch, using manual shielded metal arc welding with E6010 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-490-6

B2.1-1-205: 1996(R2007) (SWPS)...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding with E6010 (vertical uphill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-492-2

B2.1-1-207: 1996(R2007) STANDA...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-494-9

B2.1-1-209: 1996(R2007) (SWPS)...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-496-5

B2.1-1-210:2001(R2012) STANDAR...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding with consumable insert root. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This WPS was developed primarily for pipe applications.

B2.1-1-211:2001(R2012) (SWPS) ...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding with consumable insert root, followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This WPS was developed primarily for pipe applications.

B2.1-1-233: 2006 (SWPS) FOR AR...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using Argon plus 25% Carbon Dioxide shielded gas metal arc welding (short circuiting transfer mode) for the root followed by Argon plus 2% Oxygen shielded gas metal arc welding (spray transfer mode) for the balance. It cites the basemetals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-016-1

B2.1-1-235: 2006 (SWPS) FOR AR...
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using Argon plus 2% Oxygen shielded gas metal arc welding (spray transfer mode). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove and fillet welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-018-8

B2.1-1/8-014:2002 (R2013) (SWP...
This standard contains the essential welding variables for welding carbon steel to austenitic stainless steel in the thickness range of 10 through 18 gauge using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds. ISBN 0-87171-686-0

B2.1-1/8-228:2002 (R2013) (SWP...
This standard contains the essential welding variables for welding carbon steel to austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove and fillet welds. This SWPS was developed primarily for pipe applications. ISBN 0-87171-707-7

B2.1-1/8-230:2002-AMD1 (R2013)...
This standard contains the essential welding variables for welding carbon steel to austenitic stainless steel in the thickness range of 1/16 through 1-1/2 inch, using manual gas tungsten arc welding with consumable insert root. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This SWPS was developed primarily for pipe applications. ISBN 0-87171-709-3

AMD: Amendment

B2.1-22-015: 2002 (SWPS) FOR; ...
This standard contains the essential welding variables for aluminum in the thickness range of 10 through 18 gauge using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds. ISBN 0-87171-687-9

B2.1-4-217: 1999 (SWPS) FOR GA...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 3/4 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications.

B2.1-4-218: 1999 (SWPS) FOR SH...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 in. through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-593-7

B2.1-4-219: 1999 (R2009)STANDA...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 in. through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding followed by manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications.

B2.1-4-220: 1999 (SWPS) FOR; G...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 in. through 3/4 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding with a consumable insert root. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-595-3

B2.1-4-221: 1999 (SWPS) FOR; G...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding with a consumable insert root, followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-596-1

B2.1-5A-222: 1999 (SWPS) FOR; ...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 3/4 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-598-8

B2.1-5A-223: 1999 (SWPS) FOR; ...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-599-6

B2.1-5A-224: 1999 (R2009), STA...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications.

B2.1-5A-225: 1999 (SWPS) FOR G...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 3/4 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding with a consumable insert root. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-604-6

B2.1-5A-226: 1999 (SWPS) FOR G...
This standard contains the essential welding variables for chromium-molybdenum steel in the thickness range of 1/8 through 1/2 in. in the as-welded condition, or 1/8 through 1-1/2 in. in the postweld heat treated (PWHT) condition, using manual gas tungsten arc welding with a consumable insert root, followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove welds. This welding procedure specification (WPS) was developed primarily for pipe applications. ISBN 0-87171-590-2

B2.1-8-005:2002 ERRATA (R2013)...
This standard contains the essential welding variables for welding austenitic stainless steel in the thickness range of 18 through 10 gauge, using semiautomatic gas metal arc welding (short circuiting transfer mode).

It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds.

ISBN 0-87171-677-1

B2.1-8-013: 2002 (SWPS) (R2013...
This standard contains the essential welding variables for welding austenitic stainless steel in the thickness range of 18 through 10 gauge using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove welds. ISBN 0-87171-685-2

B2.1-8-024: 2001 (SWPS) FOR GA...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/16 through 1-1/2 inch, using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-693-3

B2.1-8-025: 2001 (SWPS) FOR GA...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications. ISBN 0-87171-694-1

B2.1-8-212: 2001 (SWPS) FOR; G...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/16 through 1-1/2 inch, using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. ISBN 0-87171-695-X

B2.1-8-213 1997 (SWPS) FOR; SH...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications. Historical see AWS B2.1-8-213: 1997 (R2007)

B2.1-8-213: 1997(R2012) (SWPS)...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications.

B2.1-8-214: 2001(R2012) (SWPS)...
This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications.

B2.1-BMG:2005 (HISTORICAL) Bas...
This document provides the AWS base metal grouping for welding procedure and performance qualification and is identical to Annex IV of AWS B2.1:2005, Specification for Welding Procedure and Performance Qualification. ISBN 0-87171-048-X

Free download available here

B2.1/B2.1M-BMG: 2009 - ADD1 - ...
This publication is an extract of AWS B2.1, Specification for Welding Procedure and Performance Qualification, and is identical to Annex D, Base Metal Grouping, in the 2009 edition of that standard.

This publication supersedes AWS B2.1-BMG:2005. Underlined text or a vertical line in the margin indicates a revision from the 2005 edition.

ANSI Approved.

Approx. 190 pages

ISBN 978-0-87171-748-1

B2.1: 2005 SPECIFICATION FOR W...
This specification provides the requirements for qualification of welding procedure specifications, welders, and welding operators for manual, semiautomatic, mechanized, and automatic welding. The welding processes included are oxyfuel gas welding, shielded metal arc welding, gas tungsten arc welding, submerged arc welding, gas metal arc welding, flux cored arc welding, plasma arc welding, electroslag welding, electrogas welding, electron beam welding, laser beam welding, and stud arc welding. Base metals, filler metals, qualification variables, and testing requirements are also included. ISBN 0-87171-742-5. See AWS B2.1/B2.1:2009 for new revision.

B2.2:1991 BRAZING PROCEDURE AN...
This standard provides the requirements for qualification of brazing procedure specifications, brazers, and brazing operators for manual, mechanized, and automatic brazing. The brazing processes included are torch brazing, furnace brazing, induction brazing, resistance brazing, dip brazing, and infrared brazing. Base metals, brazing filler metals, brazing fluxes, brazing atmospheres, and brazing joint clearances are also included. ISBN 0-87171-356-X

B2.3/B2.3M:2012 SPECIFICATION ...
This specification provides the requirements for qualification of soldering procedure specifications, solderers, and soldering operators for manual, mechanized, and automatic soldering.

The soldering processes included are torch soldering, furnace soldering, resistance soldering, dip soldering, infrared soldering, and induction soldering. Base metals, soldering filler metals, soldering fluxes, soldering atmospheres, and soldering joint clearances are also included.

ISBN 978-0-87171-084-0

B3.0: 1977 WELDING PROCEDURE A...
Welding Procedure and Performance Qualification (Historical - Photocopy)
Not Available for Purchase in Electronic Format

B4.0:2007 STANDARD METHODS FOR...
Mechanical test methods that are applicable to welds and welded joints are described. For each testing method, information is provided concerning applicable American National Standards Institute (ANSI), American Society for Testing and Materials (ASTM), and American Petroleum Institute (API) documents; the required testing apparatus, specimen preparation, procedure to be followed, and report requirements are also described. ISBN 978-0-87171-071-0

B4.0M: 2000 STANDARDS METHODS ...
Describes the most common mechanical test methods applicable to welds and welded joints. Each test method gives details concerning specimen preparation, test parameters, testing procedures, and report requirements. NOTE Acceptance criteria are not included but may be found elsewhere in application standards, for example. For each test method, information is provided concerning applicable American National Standards Institute ANSI, American Society for Testing and Materials ASTM, and American Petroleum Institute API documents. An expanded section on weldability testing covers cruciform, implant, Lehigh restraint, varestraint, and oblique Ygroove tests, with succinct instructions and detailed figures and schematics. Note Joint tests for brazements are covered in AWS C3.2MC3.22002. ANSI Approved. ISBN 0-87171-622-4

B5.14:2009 - SPECIFICATION FOR...
This standard establishes the minimum requirements to qualify as a Welding Sales Representative (WSR). This qualification is based on the individual’s education and experience, and his or her ability to pass an examination. ISBN 978-0-87171-746-7

B5.15:2010 - SPECIFICATION FOR...
This specification defines the requirements for the qualification of radiographic interpreters, including experience, knowledge, and skills unique to the interpretation of radiographic media and the determination of acceptance criteria for weldments and adjacent base metal. Essential to ensuring the competence of individuals engaged in radiographic interpretation are training and work experience in radiographic theory, procedures, weld and adjacent base metal defect recognition, radiographic processing, handling, storage, and code requirements relating to radiographic acceptance criteria. ANSI Approved. THIS PUBLICATION IS AVAILABLE FOR FREE DOWNLOAD (PDF). SIGN IN TO YOUR ACCOUNT AND SELECT THE "FREE DOWNLOAD" TAB IN THE RIGHT COLUMN. ISBN 978-0-87171-767-2

B5.17:2004 SPECIFICATION FOR T...
This specification establishes the minimum requirements necessary to qualify as a welding fabricator, including an examination based on the fabricators quality control manual. This document also defines the welding fabricators functions and lists reference materials that the welding fabricator should possess. ANSI Approved. Historical, Photocopy Only See AWS B5.17:2008

B5.1:2003 (ERRATA 2007) (SPANI...
This standard defines the qualification requirements for welding inspectors, which include experience, satisfactory completion of an examination, and proof of visual acuity.

The examination tests the inspectors knowledge of welding processes, welding procedures, nondestructive examinations, destructive tests, terms, definitions, symbols, reports, welding metallurgy, related mathematics, safety, quality assurance, and responsibilities. ANSI Approved.

B5.1:2013 SPECIFICATION FOR TH...
This standard defines the qualification requirements to qualify welding inspectors. The qualification requirements for visual welding inspectors include experience and satisfactory completion of an examination, which includes demonstrated capabilities, and proof of visual acuity. The examination tests the inspector’s knowledge of welding processes, welding procedures, nondestructive examinations, destructive tests, terms, definitions, symbols, reports, welding metallurgy, related mathematics, safety, quality assurance, and responsibilities.

THIS PUBLICATION IS AVAILABLE FOR FREE DOWNLOAD (PDF). SIGN IN TO YOUR ACCOUNT AND SELECT THE "FREE DOWNLOAD" TAB IN THE RIGHT COLUMN.

B5.4:2005 SPECIFICATION FOR TH...
This specification defines the requirements to qualify welder test facilities. It details the methods of qualification, test facility requirements, and the assessment requirements.THIS PUBLICATION IS AVAILABLE FOR FREE DOWNLOAD (PDF). SIGN IN TO YOUR ACCOUNT AND SELECT THE "FREE DOWNLOAD" TAB IN THE RIGHT COLUMN. ISBN 0-87171-606-2

B5.5:2011 SPECIFICATION FOR TH...
This specification defines the requirements and program to qualify Welding Educators. The qualification of a Welding Educator is determined by a combination of education and experience, satisfactory demonstration of welding performance qualification tests, and written and practical examinations. The written examination demonstrates the educatorâ??s knowledge of welding processes, weld discontinuities, destructive and nondestructive test methods, safety, welding metallurgy, weld symbols, basic arithmetic, codes, and other standards.

BHC1 - BASICS OF BRAZING ...
Chapter 1 from the Brazing Handbook. Contents for this chapter include - Introduction, Historical Perspective, Physics of Brazing, Factors Conrolling the Properties of the Brazement, The Five Elements of Brazing, Bibliography, and Suggested Reading List.

BHC11 - INTRODUCTION TO THE BR...

BHC13 - INDUCTION BRAZING ...

BHC15 - DIP BRAZING ...

BHC17 - DIFFUSION BRAZING ...

BHC19 - BRAZE WELDING ...

BHC20 - ALUMINUM AND ALUMINUM ...

BHC31 - REFRACTORY METALS: NIO...

BHC33 - ELECTRON TUBES AND VAC...

BHC35 - PIPE AND TUBING ...

BHC4 - FLUXES AND ATMOSPHERES...

BHC6 - ASSEMBLY AND FIXTURING ...

BHC8 - INSPECTION OF BRAZED JO...

BRH: 2007 BRAZING HANDBOOK, 5t...
Updated and expanded. Provides a comprehensive, organized survey of the basics of brazing, processes, and applications. Addresses the fundamentals of brazing, brazement design, brazing filler metals and fluxes, safety and health, and many other topics. Includes new chapters on induction brazing and diamond brazing. A must-have for all brazers and brazing engineers, and students. ISBN 978-0-87171-046-8

BRS BRAZE SAFETY ***SET OF 25 ...
Avoid the hazards of brazing processes. This booklet outlines precautionary measures and safe practices that promote safety and continued productivity.

BUNDLE A:2009...
Save a bundle when you buy an AWS structural bundle. Get 15% OFF the individual standards purchase prices.

Contains:

AWS D1.1/D1.1M:2008, and most recent editions of AWS A2.4 and AWS A3.0

BUNDLE B :2012...
Save a bundle when you buy an AWS structural bundle. Get 15% OFF the individual standards- purchase prices.

Contains:

AWS D1.1/D1.1M:2010, and the most recent editions of:
D1.2/D1.2M
D1.3/D1.3M
D1.6/D1.6M
D1.4/D1.4M
AASHTO/AWS D1.5M/D1.5

Individual catalog prices: Nonmembers: $1,548, AWS members: $1,161.00
Not Available for Purchase in Electronic Format

BUNDLE B: 2007...

Save a bundle when you buy an AWS Structural bundle, Get 15% OFF the individual stardards' purchase prices

Contains:

AWS D1.1/D1.1M: 2006 / AWS D1.2/D1.2M: 2003 / AWS D1.3/D1.3M: 2007 / AWS D1.4/D1.4M :2005 / AASHTO/AWS D1.5M/D1.5: 2007 and AWS D1.6/D1.6M :2007

BUNDLE C: 2012...
Save a bundle when you buy an AWS structural bundle. Get 15% OFF the individual standards purchase prices.

Contains most recent editions of:
AWS A2.4
AASHTO/AWS D1.5M/D1.5.

Individual catalog prices: Nonmembers: $496.00, AWS members: $372.00
Not Available for Purchase in Electronic Format

BUNDLE D:2012 (SEISMIC BUNDLE)...
Save a bundle when you buy an AWS structural bundle. Get 15% OFF the individual standards purchase prices.

Contains:

AWS D1.1/D1.1M:2010
D1.8/D1.8M:2009.

Individual catalog prices: $656.00 Nonmembers and $492.00 Members
Not Available for Purchase in Electronic Format

BUNDLE-CRWT RESISTANCE WELDING...

Save a bundle when you buy an AWS resistance welding bundle. Receive 15% OFF the individual standards' purchase price.

This bundle contains:

1) RWMA Resistance Welding Manual, Revised 4th Edition

2) RWMA Bulletin #5, Resistance Welding Control Standard

3) RWMA Bulletin #14, Maintenance Manual for Resistance Welding Machines

4) RWMA Bulletin #16, Resistance Welding Equipment Standards

5) AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination

C1.1M/C1.1:2012 RECOMMENDED PR...
This Recommended Practice is a collection of data and procedures that are intended to assist the user in setting up resistance welding equipment to produce resistance welded production parts.

While the recommendations included are not expected to be final procedures for every production part or every welding machine, they serve as starting points from which a user can establish acceptable welding machine settings for specific production welding applications.

In some cases, recommended machine data is not available. In these instances, some description of the process is given to assist the reader in determining if the process might be suitable for application. 

C1.4M/C1.4: 2009 SPECIFICATION...
This specification provides the shear strength and weld button diameter requirements for carbon steel and low-alloy steel sheet resistance and projection welds. I SBN 978-0-87171-511-1

C1.5:2005 SPECIFICATION FOR TH...
Establishes requirements for qualification of resistance welding technicians. Defines minimum experience, examination, application, qualification, and requalification requirements and methods. Provides a method for technicians to establish a record of their qualification and abilities, such as development of machine troubleshooting, processes controls, quality standards, and problem solving. ISBN 0-87171-735-2

C2.16/C2.16M:2002 GUIDE FOR TH...
This guide contains recommendations for thermal-spray operator qualification based on knowledge and skill testing. Twelve individual thermal-spray operator qualification tests (TSOQT) are included for engineering and corrosion control applications: one each for job knowledge, high velocity oxygen fuel (HVOF) spraying and flame spray-fusing, two for arc spraying, and three each for flame spraying and air-plasma spraying. ISBN 0-87171-702-6

C2.1: 1973 RECOMMENDED SAFE PR...
RECOMMENDED SAFE PRACTICES FOR THERMAL SPRAYING - HISTORICAL COPY ** AVAILABLE ONLY AS A PHOTOCOPY **
Not Available for Purchase in Electronic Format

C2.20/C2.20M:2002 SPECIFICATIO...
Explains metalized zinc cathodic protection systems for corrosion protection of concrete structures with steel reinforcing. A publication useful to departments of transportation, port facilities, power plants, and other operations responsible for repair and maintenance of concrete structures affected by corrosion of steel reinforcement. Includes information on job safety, passfail reference standards, feedstock materials, needed equipment, and instructions for surface preparation, thermal spraying, and quality control. ANSI Approved. ISBN 0-87171-468-X

C2.23M/C2.23:2003 SPECIFICATIO...
Suggested for use by owners and design, fabrication, and maintenance engineers to detail and contract for the application of thermal spray coatings TSC for the preservation and maintenance of steel structures. Also may be used by TSC inspectors and applicators to develop and maintain application procedures, equipment inventory, and an operatortraining program. ISBN 0-87171-713-1

C3.11M/C3.11:2011 SPECIFICATIO...
This specification presents the minimum process and quality requirements for the torch soldering of ceramics, precious metals, and refractory metals, as well as the alloys of copper, iron, nickel, aluminum, magnesium, tin, lead, and zinc.

The purpose of this specification is to standardize torch soldering process requirements that will ensure that soldered joints attain the quality level designated by the application. This document establishes the minimum requirements for processes using a minimum amount of explanatory information so as to limit any ambiguity. This document assigns responsibility for soldered joint quality to the Organization Having Quality Responsibility and permits that organization to modify requirements as necessary. However, this specification requires that proper documentation be developed and archived by that organization, which explains the basis and specific details of any such modifications.

C3.2M/C3.2:2008 STANDARD METHO...
This standard describes the test methods used to obtain brazed strength data of the short-time testing of single-lap joints in shear, butt-tension, stress-rupture, creep-strength, four-point-bending, and ceramic-tensile-button specimens. Specimen preparation methods, brazing procedures, testing techniques, and methods for data analysis are detailed. Sample forms for recording data are presented. A graphical method of data presentation relates shear stress to overlap distance. ISBN 978-0-87171-086-4

C3.3: 2008 RECOMMENDED PRACTIC...
This standard lists the necessary steps to assure the suitability of brazed components for critical applications. Although such applications vary widely, they have certain common considerations with respect to materials, design, manufacture, and inspection. It is the intent of this document to identify and explain these common considerations and the best techniques for dealing with them. It is beyond the scope of this document to provide specific details on these techniques, which the user must adapt to fit each particular application. ISBN 978-0-87171-092-5

C3.4:1999 SPECIFICATION FOR TO...
Provides the minimum fabrication, equipment, process procedure requirements, and inspection requirements for the torch brazing of copper, copper alloys, heat and corrosion resistant alloys, and other materials that can be adequately torch brazed. ANSI Approved. (Historical - Photocopy) See AWS C3.4M/C3.4:2007
Not Available for Purchase in Electronic Format

C3.5:1999 SPECIFICATION FOR IN...
This specification provides minimum fabrication, equipment, material, process procedure requirements, and inspection requirements for the induction brazing of steels, copper, copper alloys, and heat and corrosion resistant alloys and other materials that can be adequately induction brazed. For the brazing of aluminum alloys refer to AWS C3.7, Specification for Aluminum Brazing. This specification provides criteria for classifying induction brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability of each class. The specification defines acceptable induction brazing equipment, materials, and procedures, as well as the required inspection for each class of joint. (Historical - Photocopy) See AWS C3.5/C3.5M:2007
Not Available for Purchase in Electronic Format

C3.6:1999 SPECIFICATION FOR FU...
This specification provides minimum fabrication, equipment, material, process procedure requirements, and inspection requirements for the furnace brazing of steels, copper, copper alloys, and heat and corrosion resistant alloys and other materials that can be adequately furnace brazed. For the brazing of aluminum alloys refer to AWS C3.7, Specification for Aluminum Brazing. This specification provides criteria for classifying furnace brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability of each class. The specification defines acceptable furnace brazing equipment, materials, and procedures, as well as the required inspection for each class of joint. (HISTORICAL - PHOTOCOPY)
Not Available for Purchase in Electronic Format

C3.7/C3.7M:2005 SPECIFICATION ...
Addresses the minimum fabrication, equipment, material, process procedure requirements, and inspection requirements for aluminum brazing using the atmosphere furnace, vacuum furnace, and flux processes. ANSI Approved. ISBN 0-87171-022-6

C3.8M/C3.8:2005 SPECIFICATION ...
This specification presents minimum fabrication, equipment, and process procedure requirements for the ultrasonic examination of brazed joints. Its purpose is to standardize brazed-joint ultrasonic examination requirements for all applications in which brazed joints of assured quality are required. It provides minimum requirements for equipment, procedures, and the documentation of such tests. Requirements for ultrasonic test instruments and accessory equipment, such as tanks, turntables, bridges, carriages, manipulators, transducers, alarms, and couplets. ANSI Approved. ISBN 0-87171-009-9

C3.9M/C3.9: 2009 SPECIFICATION...
This specification provides the minimum fabrication, equipment, material, and process procedure requirements, as well as discontinuity limits for the resistance brazing of steels, copper, copper alloys, heat- and corrosion-resistant alloys, and other materials that can be adequately resistance brazed (the resistance brazing of aluminum alloys is addressed in AWS C3.7M/C3.7, Specification for Aluminum Brazing). This specification provides criteria for classifying resistance brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability in each class. This specification defines acceptable resistance brazing equipment, materials, and procedures, as well as the required inspection for each class of joint. ISBN 978-0-87171-510-4

C4.1-77 SET, CRITERIA FOR DESC...
This document is an aid to assist users, inspectors, and producers in communicating among one another their needs with regard to the oxygen-cut surface.
Not Available for Purchase in Electronic Format

C4.2/C4.2M:2009 RECOMMENDED PR...
Revised and expanded, describes the oxyfuel gas cutting process and presents the latest procedures and safety requirements, using terminology and practices compatible with International Organization for Standardization (ISO) documents. Illustrations show torch and nozzle configurations, and examples of production-cut surfaces. ANSI Approved. approx. 53 pages ISBN 978-0-87171-750-4

C4.3/C4.3M:2007 RECOMMENDED PR...
The newly revised manual for oxyfuel gas heating torch operation includes the latest procedures to be used in conjunction with oxifuel gas heating equipment. The manual also includes the latest safety requirements. Complete lists of equipment are available from individual manufactures.  ISBN 978-0-87171-070-3

C4.4/C4.4M:2007 RECOMMENDED PR...
This second edition of Recommended Practices for Heat Shaping and Straightening covers the shaping of metal products by prudent use of heat to obtain a desired configuration. The text reviews the theory and analytical calculations that explain how heat shaping and straightening occurs. Sample calculations and tables are presented for typical materials. General heating patterns and heat shaping and straightening techniques are discussed. Specific heating applications are illustrated for various sections. ISBN 978-0-87171-079-6

C4.5M:2006 UNIFORM DESIGNATION...
This publication proposes a marking system that will include the name, registration trademark, correct fuel gas symbol, nozzle cutting capacity, and a code or part number to permit easy reference to the manufacturers operating data. C4.5M provides a common identification system that will result in the safe operation of oxyfuel nozzles, i.e., operators will know they are using the correct nozzle for the job being performed. Oxyfuel nozzles covered by the document include those for cutting, welding, heating, and brazing. ANSI Approved. ISBN 0-87171-033-1

C4.6M:2006 (ISO 9013:2002 IDT)...
This is the U.S. national adoption of ISO 9013:2002, Thermal cutting - Classification of thermal cuts - Geometric product specification and quality tolerances. It includes three national annexes (Criteria for Describing Oxygen-Cut  Surfaces with a photograph of a Surface Roughness Guide, a list of reference documents available for individuals involved with Oxyfuel Gas Welding and Cutting, and a guide for the preparation of technical inquiries to AWS) as well as a list of published AWS documents on Oxyfuel Gas Welding and Cutting. ISBN 0-87171-012-9

C5.10/C5.10M:2003 RECOMMENDED ...
This document is concerned with six industrial gases: argon (Ar), carbon dioxide (CO2), helium (He), hydrogen (H), nitrogen (N), and oxygen (O). Properties, uses, safe handling, distribution, mixtures and effects on arc characteristics and welds are presented for flux cored arc welding (FCAW), gas tungsten arc welding (GTAW), gas metal arc welding (GMAW), electrogas welding (EGW), plasma arc welding (PAW), plasma arc cutting (PAC), laser welding (LW) and laser cutting (LC). Gas purging, gas distribution and safety practices are also covered. ISBN 0-87171-711-5

C5.2: 2001 RECOMMENDED PRACTIC...
With the increasing use of plasma arc cutting for a variety of metals in industry, this standard is a great tool to optimize and troubleshoot your plasma arc cutting operations. It discusses basics of the process, components, controls, power supplies, and recommended process consumables and parameters and it gives you methods of optimizing cut quality and parameter settings. The also standard deals with safety and health aspects of the process, and methods for control of pollution and other hazards. ANSI Approved. ISBN 0-87171-648-8

C5.4:1993 (ERRATA) RECOMMENDED...
These recommended practices for stud welding, prepared by the Subcommittee on Stud Welding of the AWS Committee on Arc Welding and Cutting, are intended to serve as a basic guide for those interested in attaching fasteners by arc and capacitor discharge stud welding. The variations of the process, stud design, equipment, welding procedures, quality control, and safety precautions are discussed. The information presented will guide the designer and the shop in the utilization of studs in many fields including automotive manufacture, boiler and building construction, farm and industrial equipment, railroads and shipbuilding, aircraft and aerospace, metal furniture, and other metal working industries. ISBN 0-87171-418-3

C5.5/C5.5M -2003 RECOMMENDED P...
The first completely new treatment of gas tungsten arc welding GTAW since 1980, this comprehensive document is an indispensable tool for operators, supervisors, trainers, and other GTAW professionals. The standard presents recommended practices for the GTAW process. It provides a fundamental explanation of the process, describes basic practices and concepts, and outlines advanced methods and applications. These features should help welding personnel determine the best applications of GTAW, and apply it in manual and automated operations. This edition addresses the present uses of GTAW in the metalfabricating industry, new applications, and advances in research and development. It provides many practical recommendations on the use of GTAW, and a handy troubleshooting section. Contents include Process Advantages and Limitations Equipment and Supplies Tungsten Electrodes Gas Shielding, Purging, and Backing Fixturing and Tooling Welding Techniques Joint Design, Preparation, and Welding Positions Welding Characteristics of Selected Alloys Quality Control Troubleshooting and Safety ANSI Approved. ISBN 0-87171-715-8

C6.1-89 (R2009) RECOMMENDED PR...
This recommended practice describes friction welding fundamentals and basic equipment requirements. Suggested procedure qualification, inspection methods, and joint designs are detailed. Typical mechanical property data are referenced. ISBN 0-87171-309-8

C6.2/C6.2M:2006 SPECIFICATION ...
This specification provides for the qualification of friction welding machines, procedures, and training of welding operators. Qualification of the welding procedure specification (WPS) includes the material specifications involved, weld joint design, destructive and nondestructive examination requirements, as well as guidelines for different categories of quality assurance. Qualification of welding equipment includes weld parameter control and weld reproducibility. Welding operators require training in the proper operation of friction welding equipment. The requirements for requalification of the WPS and equipment are also given. ISBN 0-87171-631-3

C7.2:1998 RECOMMENDED PRACTICE...
This document presents recommended practices for laser beam welding, cutting, and drilling. It is intended to cover common applications of the process. Processes definitions, safe practices, general process requirements and inspection criteria are provided. ISBN 0-87171-562-7

C7.3:1999 (R2003) PROCESS SPEC...
Sister publication to C7.1 Recommended Practices for Electron Beam Welding, this standard discusses applicable specifications, safety, requirements, fabrication, quality examination, equipment calibration and maintenance, approval, and delivery of work. Includes sample WPS and PQR forms, as well as an economic Nondestructive Evaluation Discontinuity Limits chart. C7.1 is a best of industry practices standard that uses should while this standard uses shall. ANSI Approved. This is the 2003 reaffirmation version. ISBN 0-87171-586-4

CAWF CHARACTERIZATION OF ARC W...
Six welding fumes, representing a variety of welding rods and wires, were analyzed for particle size and chemistry by X-ray diffraction, energy dispersive X-ray analysis, scanning transmission electron microscope, and automated electron beam analysis. Four carbon steel fumes (E6010, E7018, E70S-3, E70T-1), a stainless steel fume (E308-16) and an aluminum fume (E5356) were tested. It was found that particle average diameters are all in the respirable range â?? between 0.1 and 1.0 µM. Few individual particles were greater than 1 µM, but STEM pictures revealed many particles as small as 0.01 µM. The particles appeared to be spheres or clusters of spheres. Even though no crystalline features were observed, all particles examined produced electron diffraction patterns, indicating that they contained crystalline material. There was no correlation between average diameter and particle chemistry or between average diameter and fume type. An analysis of particle chemistry indicates that the potential toxicity of the fumes does vary appreciably. ISBN 0-87171-229-6

CCRM:2010 - AWS D1.1 STRUCTURA...
Official textbook for CWI preparatory seminar. Helps CWI candidates prepare for the open-book portion of the CWI examination, which tests ability to navigate through a code and find correct answers within a specified time.

AWS Education Services publishes the AWS Code Clinic Workbook to guide and assist quality professionals – inspectors, supervisors, etc. – and quality-conscious engineers and managers in reading, understanding, and learning to apply industrial codes such as the Structural Welding Code—Steel. AWS D1.1: 2010 covers the welding requirements for any type of welded structure made from the commonly used carbon and low-alloy steels.

Includes practice questions similar to the exam questions, and the answers.

CM CERTIFICATION MANUAL FOR WE...
Selfstudy to prepare for AWS welding inspector exams. An excellent reference and introduction for those studying for the CWI examination. An updated version of the bestseller used by thousands of CWI candidates since 1977, now with a sleeker style and improved readability. Veteran editor Eugene Hornberger an SCWI has taught the AWS exam preparatory seminar for years. Hes packed this latest edition with a wealth of insights. Chapters cover the welding inspectors responsibilities standards joint geometry and terminology symbols, weldability destructive testing procedure and welder qualification welding, brazing, and cutting processes discontinuities NDE and inspector reports. Each chapter concludes with a selfadministered test similar in content and style to the actual CWI exam questions. Features a contemporary layout that includes tip boxes. This book has been invaluable to literally thousands of CWI applicants who studied on their own for the AWS CWI exam.dy to prepare for AWS welding inspector exams ISBN 0-87171-626-7

CWSR 2010 WELDING SALES REPRES...
The Welding Sales Representative workshop is designed for the welding distributor and manufacturer with the intent of introducing basic welding knowledge. This two and half say program is not intended to help the participants welders; rather reinforce basic processes and equipment that are generic to all sales representatives. The workshop focuses on safety in welding, cutting and allied processes, training on the fundamental principles of general welding operations and processes, basic arc equipment, shielding gases, consumables, and related components.
Not Available for Purchase in Electronic Format

D1.1 BI THE OFFICIAL BOOK OF D...
A collection of responses to formal inquiries about the requirements of AWS D1.1 from 1976 to 1998. An excellent reference for AWS D1.1 users. (Historical)

D1.1/D1.1M: 2006 STRUCTURAL WE...
For everyone involved in any phase of welding steel structures - engineers, detailers, fabricators, erectors, inspectors, etc. - the new 540-page edition of D1.1 spells out the requirements for design, procedures, qualification, fabrication, inspection, and repair. A wide range of projects, repairs, and product forms come under its authority, including pipe, plate, and structural shapes that are subject to either static or cyclical stresses. Dozens of updates to the Structural Welding Code-Steel make the 2006 edition indispensable for anyone designing, building, or inspecting steel structures and products. ISBN 0-87171-025-0

D1.1/D1.1M: 2010 (2ND PRINTING...
For everyone involved in any phase of welding steel structures - engineers, detailers, fabricators, erectors, inspectors, etc. - the new D1.1 spells out the requirements for design, procedures, qualification, fabrication, inspection, and repair of pipe, plate, and structural shapes that are subject to either static or cyclical stresses. U.S. Customary and SI units of measurement.

This code covers the welding requirements for any type of welded structure made from the commonly used carbon and low-alloy constructional steels. Clauses 1 through 8 constitute a body of rules for the regulation of welding in steel construction. There are eight normative and twelve informative annexes in this code.

570 pages, 21 annexes, 171 figures, 78 tables, (2010).

Click here to purchase the D1.1/D1.1M: 2010 version in Spanish

Click here to purchase the D1.1/D1.1M: 2010 version in Portuguese

Click here to purchase the D1.1/D1.1M: 2010 version in Russian

Click here to purchase the D1.1/D1.1M: 2010 version in Chinese

D1.1/D1.1M: 2010 (PORTUGUESE) ...
First Edition Translation of the D1.1 Structural Welding Code — Steel Publication!

First direct, accurate and concise translation of the world famous Structural Welding Code — Steel. It has been created in the same format as the version in English, including all of the necessary tables and figures. Every single Annex and Commentary sections has been reproduced from the original version.

D1.1/D1.1M:2010 Structural Welding Code — Steel
For everyone involved in any phase of welding steel structures - engineers, detailers, fabricators, erectors, inspectors, etc. - the new D1.1 spells out the requirements for design, procedures, qualification, fabrication, inspection, and repair of pipe, plate, and structural shapes that are subject to either static or cyclical stresses. U.S. Customary and SI units of measurement.

D1.1/D1.1M:2010 Código de Soldagem Estrutural — Aço
Este código aborda os requisitos de soldagem para qualquer tipo de estrutura soldada feita com aços construtivos de carbono e baixa liga. As cláusulas 1 a 8 constituem um corpo de regras para a regulamentação de solda nas construções com aço. Neste código existem nove anexos ormativos e doze informativos. Comentários sobre o código estão inclusosn este documento.

Click here to purchase the D1.1/D1.1M: 2010 version in English

Click here to purchase the D1.1/D1.1M: 2010 version in Spanish

Click here to purchase the D1.1/D1.1M: 2010 version in Russian

Click here to purchase the D1.1/D1.1M: 2010 version in Chinese

D1.1/D1.1M: 2010 (SPANISH) ST...
First Edition Translation of the D1.1 Structural Welding Code — Steel Publication!

First direct, accurate and concise translation of the world famous Structural Welding Code — Steel. It has been created in the same format as the version in English, including all of the necessary tables and figures. Every single Annex and Commentary sections has been reproduced from the original version.

D1.1/D1.1M:2010 Structural Welding Code — Steel
For everyone involved in any phase of welding steel structures - engineers, detailers, fabricators, erectors, inspectors, etc. - the new D1.1 spells out the requirements for design, procedures, qualification, fabrication, inspection, and repair of pipe, plate, and structural shapes that are subject to either static or cyclical stresses. U.S. Customary and SI units of measurement.

D1.1/D1.1M:2010 Código de Soldadura Estructural — Acero
Este código cubre los requerimientos para cualquier tipo de estructura soldada realizada con acero al carbono y de baja aleación para construcción. Las primeras ocho secciones constituyen un conjunto de reglas para la regulación de soldaduras en la construcción con acero. Se incluyen ocho anexos normativos y doce anexos informativos en este código. También se incluyen, en este documento, comentarios del código.

Click here to purchase the D1.1/D1.1M: 2010 version in English

Click here to purchase the D1.1/D1.1M: 2010 version in Portuguese

Click here to purchase the D1.1/D1.1M: 2010 version in Russian

Click here to purchase the D1.1/D1.1M: 2010 version in Chinese

D1.1/D1.1M:2008 (SPANISH) CODI...
D1.1/D1.1M:2008 Código de Soldadura Estructural — Acero PROMOCION FINAL

Este código cubre los requerimientos para cualquier tipo de estructura soldada realizada con acero al carbono y de baja aleación para construcción. Las primeras ocho secciones constituyen un conjunto de reglas para la regulación de soldaduras en la construcción con acero. Se incluyen ocho anexos normativos y doce anexos informativos en este código. También se incluyen, en este documento, comentarios del código.

¡Y reciba una B1.11/2000 AWS B1.11:2000 Guia para la Examinación Visual de Soldaduras GRATIS!

D1.1: 1972 STRUCTURAL WELDING ...
D1.1: 1972 STRUCTURAL WELDING CODE (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1979 STRUCTURAL WELDING ...
AWS D1.1: 1979 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1981 STRUCTURAL WELDING ...
AWS D1.1: 1981 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1983 STRUCTURAL WELDING ...
AWS D1.1: 1983 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1985 STRUCTURAL WELDING ...
AWS D1.1: 1985 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1990 STRUCTURAL WELDING ...
AWS D1.1: 1990 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.1: 1994 STRUCTURAL WELDING ...
AWS D1.1: 1994 STRUCTURAL WELDING CODE - STEEL (HISTORICAL)

D1.1: 1998 STRUCTURAL WELDING ...
AWS D1.1: 1998 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)

D1.1:1988 STRUCTURAL WELDING C...
AWS D1.1:1988 STRUCTURAL WELDING CODE - STEEL (HISTORICAL, PHOTOCOPY ONLY)
Not Available for Purchase in Electronic Format

D1.2 -1997 STRUCTURAL WELDING ...
STRUCTURAL WELDING CODE - ALUMINUM REV. 1997 HISTORICAL - 228 PAGES (PHOTOCOPY)
Not Available for Purchase in Electronic Format

D1.2/D1.2M: 2008 STRUCTURAL WE...
Covers welding requirements for any type of structure made from aluminum structural alloys, except aluminum pressure vessels and fluid-carrying pipelines. Includes sections on design of welded connections, procedure and performance qualification, fabrication, inspection, stud welding, and strengthening and repair of existing structures. A commentary offers guidance on interpreting and applying the code. 226 pages, 59 figures, 24 tables, (2008).

D1.3: 1989 STRUCTURAL WELDING ...
Historical copy for new revision see AWS D1.3/D1.3M Rev. 2008
Not Available for Purchase in Electronic Format

D1.4/D1.4M-1998 STRUCTURAL WEL...
AWS D1.4/D1.4M-1998 STRUCTURAL WELDING CODE - REINFORCING STEEL (HISTORICAL - PHOTOCOPY)
Not Available for Purchase in Electronic Format

D1.4/D1.4M:2011 Structural Wel...
Covers welding of reinforcing steel in most reinforced concrete applications. Includes sections on allowable stresses, structural details, workmanship requirements, technique, procedure and performance qualification, and inspection. Figures clearly illustrate important welding considerations: unacceptable weld profiles, effective weld sizes, details of joints of anchorage, base plates, and inserts. Now addresses precast concrete components. Clarification on prequalified details and essential variables for fillet welds. New table illustrates acceptance criteria for macro tech tests. Approx 85 pages. (2011)

D1.6/D1.6M:2007 STRUCTURAL WEL...
Covers requirements for welding stainless steel structural assemblies/components (excluding pressure vessels or pressure piping) using gas metal arc welding, shielded metal arc welding, flux cored arc welding, submerged arc welding, and stud welding. Allows prequalified Welding

Procedure Specifications for the austenitic stainless steels based on considerable experience with the most widely used stainless steels. Sections include design, procedure and performance qualification, fabrication, inspection, and stud welding.

292 pages, 14 annexes, 80 figures, 29 tables.

D1.7/D1.7M:2010;Guide for Stre...
Provides engineers and contractors with general direction and guidance on weld repairs, weld strengthening, and other procedures to correct problematic issues with existing structures made of steel (minimum yield strength of 100 ksi and minimum thickness of 1⁄8 inch), cast iron, and wrought iron. 52 pages, 4 tables, (2009).

D1.8/D1.8M :2009 STRUCTURAL WE...
A supplement to AWS D1.1, Structural Welding Code—Steel. Applicable to welded joints in seismic load resisting systems designed in accordance with the Seismic Provisions of the American Institute of Steel Construction, Inc. Covers additional controls on detailing, materials, workmanship, testing, and inspection necessary to achieve adequate performance of welded steel structures under conditions of severe earthquake- induced inelastic straining. Includes a commentary offering guidance on interpreting and applying this supple-ment. 124 pages, 9 annexes, commentary, 22 figures, 8 tables, (2009).

D1.9/D1.9M:2007 STRUCTURAL WEL...
This code covers the requirements for design and welding of any type of titanium structure. Titanium pressure vessels and fluid-carrying pipe lines are specifically excluded.

Clauses 1 through 5 and Annex A constitute a body of rules for the regulation of welding in titanium construction. A commentary on the code is also included with the document.

160 pages, commentary, 6 annexes, 53 figures, 19 tables, (2007).

D10.10/D10/10M -1999 (R2009) R...
This standard provides information on recommended practices, equipment, temperature control, insulation, and advantages and disadvantages for the methods presently available for local heating of welded joints in pipe and tubing.

D10.11M/D10.11:2007 GUIDE FOR ...
This standard presents guidelines for welding the root pass of metal pipe butt joints with an open root or a consumable insert. Joint designs, assembly, consumable insert configurations, base metals, filler metals, and purging are discussed. Applicable arc welding processes and techniques are described. ANSI Approved. approx. 22 pages ISBN 0-87171-644-5

D10.13/D10.13M:2001 RECOMMENDE...
This document provides the minimum requirements for brazing of copper tubing for medical gas and vacuum distribution systems in healthcare facilities. It contains criteria for the preparation and cleanliness of materials and equipment, joint heating and filler metal application techniques, and inspection and testing options. ANSI Approved. ISBN 0-87171-571-6

D10.18M/D10.18:2008 GUIDE FOR ...
This standard presents a detailed discussion of the metallurgical and welding characteristics and weldability of duplex stainless steel used in piping and tubing. A number of tables and graphs are presented in order to illustrate the text. ISBN 978-0-87171-088-8

D10.6/D10.6M: 2000 RECOMMENDED...
Incorporates results of research on the effects of atmospheric exposure during welding. Recommended maximum exposure temperature has been lowered and the effects of high temperature exposure have been revised. Provides coverage on power sources, tungsten electrodes, titanium base metal grades, filler metals, joint design and preparation, pickling and cleaning, fitting and tacking, preweld cleaning, gas shielding, welding procedures and techniques, and preheat and postweld heat treatment. Also includes information on weld quality tests and safety. ANSI Approved. ISBN 0-87171-623-2

D10.7M/D10.7:2008 GUIDE FOR TH...
This document presents information concerning those properties of aluminum which affect its weldability and which cause specific problems in the fabrication of aluminum pipe. Recommendations are made for solving these problems and suggested procedures are presented for welding aluminum pipe joints with the Gas Tungsten Arc and Gas Metal Arc Welding Processes. ISBN 978-0-87171-099-4

D10.9-69...

Not Available for Purchase in Electronic Format

D14.1/D14.1M:2005 SPECIFICATIO...
Requirements are presented for the design and fabrication of constructional steel weldments that are used in industrial and mill cranes, lifting devices and other material handling equipment. Requirements are also included for modification, weld repair, and postweld treatments of new and existing weldments. Filler metal and welding procedure guidelines are recommended for the applicable base metals, which are limited to carbon and low-alloy steels. Allowable unit stresses are provided for weld metal and base metal for various cyclically loaded joint designs. ISBN 0-87171-736-0

D14.3/D14.3M:2005 SPECIFICATIO...
This specification provides standards for producing structural welds used in the manufacture of earthmoving, construction, and agricultural equipment. Such equipment is defined as self-propelled, on- and off-highway machinery and associated implements. Manufacturerâ??s responsibilities are presented as they relate to the welding practices that have been proven successful within the industry in the production of weldments on this equipment. Basic dimensional weld details are defined and interpreted for application throughout the document. Provisions are made to identify base metals used in these weldments. Procedures to assure they are welded with compatible, identifiable welding processes and consumables are included with consideration given to factors that affect weldability. ISBN 0-87171-741-7

D14.4/D14.4M:2005 SPECIFICATIO...
This specification establishes common acceptance criteria for classifying and applying carbon and low-alloy steel welded joints used in the manufacture of machines and equipment. It also covers weld joint design, workmanship, quality control requirements and procedures, welding operator and welding procedure qualification, weld joint inspection (visual, radiographic, ultrasonic, magnetic particle, liquid penetrant), repair of weld defects, and heat treatment. ISBN 0-87171-733-6